Did you know?

Check the electrode gap of the spark plug and ensure it is 0.02 inches. Always change the spark plug after 100 operating hours of the chainsaw to avoid engine problems. Check the chain tension and adjust it if it is too loose or tight. Use an adjustable wrench to loosen the two nuts on both sides of the chainsaw.3. Drive shaft Problem. You might experience drive shaft problems with a Stihl pole saw model HT131. The drive shaft stops engaging after slipping out by roughly an inch. If you think you put the drive shaft back together correctly after it fell apart on the HT 133, the entire unit would start spinning. The fix. Pole Saw Stihl HT 102 Instruction Manual. Pole pruner (104 pages) Summary of Contents for Stihl HT 131. Page 1 STIHL HT 100, 101, 130, ... Page 8 (e.g. reduced field of vision), problems with hearing, dizziness, deterioration in ability to concentrate. Apart from other possibilities, these symptoms may be caused by an excessively high ...

The compression will go down on a warm/hot engine and the Stihl is getting weak if it's at or below 100 hot and suspicious if 125 hot or cold, but I have an old 028 in 125-130 area and it still starts/cuts good and rope pull feels good compression and piston not scored so I just keep on running it. It's a 30 year old saw.Lawn and Garden Equipment Stihl HT 56 C Instruction Manual. (20 pages) Pole Saw Stihl HT 250 Instruction Manual. (96 pages) Pole Saw Stihl HT Instruction Manual. (72 pages) Pole Saw Stihl HT-KM Instruction Manual. (60 pages) Pole Saw Stihl HT-KM Instruction Manual. The saw passes all 3 vacuum and pressure leakage tests for the carb and crankcase. The spark plug was replaced not long before I got serious about solving this. Also replaced: - a fuel hose - in-tank fuel filter - auxiliary air filter - spark arrest screen - exhaust gasket - decompression valve (lets the Stihl start easier with less kick-back)The pole pruner must not be used for felling operations. The pole pruner may be used in the rain. The pole pruner is powered by a STIHL AP battery or a STIHL AR battery. WARNING ￭ Batteries not explicitly approved for the pole pruner by STIHL may cause a fire or explosion. Persons may be seriously or fatally injured and property may be damaged.

The German brand has dedicated the last century to producing products that are efficient, durable, affordable, and easy to use. On any Stihl machine the on position of a switch is signified by the I or 1 symbol and the off position or kill switch position is designated by the O symbol. This is also true for most brands of landscaping equipment ...Inspect the Sprocket. If you performed all the required maintenance tasks and are sure the engine runs well but the chain still doesn't turn, it's time to inspect the sprocket. That procedure requires removing the chain; before you do that task, disable the saw by removing the spark plug wire. Then remove the clutch cover by loosening the nuts ...Stihl HT101 Pole Saw repair chain will not turn. FLORIDA WATERMEDIC. 163 subscribers. Subscribe. Subscribed. 1. 2. 3. 4. ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Stihl pole saw troubleshooting. Possible cause: Not clear stihl pole saw troubleshooting.

Download 31 Stihl Pole Saw PDF manuals. User manuals, Stihl Pole Saw Operating guides and Service manuals.Table of Contents hide. Common Chainsaw Problems & Solutions. Problem 1: Chainsaw Won’t Start. Problem 2: Chainsaw Starts, Stalls & Dies. Problem 3: Chainsaw Chain Won’t Turn or Move. Problem 4: Chainsaw Runs With the Choke On. Problem 5: Chainsaw Loses Power and Bogs Down. 6. Chainsaw Is Smoking.

3. Drive shaft Problem. You might experience drive shaft problems with a Stihl pole saw model HT131. The drive shaft stops engaging after slipping out by roughly an inch. If you think you put the drive shaft back together correctly after it fell apart on the HT 133, the entire unit would start spinning. The fix. Sep 2, 2018 · Hello all, I am troubleshooting a Stihl HT131. It works fine when the pole is retracted however when you extend it out all the way the chain does not spin. I took apart the shaft and couldn't see anything obvious. The star ends of the shaft seem fine as well as the bearings. The female ends of the engine and head seem ok also.

timcast irl lydia left Dec 3, 2008. #4. carvinmark said: Lack of oil, may be the bar is plugged up where the oil enters. Check if the hole is clear. +1, Stihl saws don't pump out the oil, so make sure everything is clean like the oil outlets, the bar grooves and the sprocket tip of the bar. Also check your clutch sprocket for wear.3.45K subscribers Subscribe 68K views 2 years ago PERRY A step by step guide to the disassembly and assembly of a Stihl HT-101 pole saw and Stihl HT-75 pole saw shaft assembly. A lot... davita dialysis pay rateruby may erome Check the oil pump, the oil tank vent, and the oil outlets around the clutch. If any of these are clogged, oil pressure may be building up until oil leaks out of the lines inside the tool. This oil then builds up inside the body of the chainsaw, and drips out through unsealed parts of the casing while in storage.Feb 28, 2018 · STIHL HT-101 POLE SAW, shaft repair/replacement. I have recently made a newer improved video of this. STIHL HT-101 POLE SAW, shaft repair/replacement. teva 74 white round pill Nov 26, 2022 · If not, remove the cover, carefully stripping the screw, and separate it from the saw. Inspect the tension gear precisely. If there is any damage, you have to replace it with the manual as it varies according to the models. To check the guide bar, remove the chain first. Then, move aside the bar to inspect it. plainridge entriesvistaprint pensestatesales org nh 01 - Stihl Chainsaw Spark Arrestor. The spark arrestor is a small screen that prevents the engine from emitting sparks. Over time, the spark arrestor can become clogged with soot. If the spark arrestor is clogged, the chainsaw may run stall or run rough. To unclog the spark arrestor, remove it and clean it with a wire brush. listcrawler grand junction 4M Ranch 4.69K subscribers Join 20K views 4 years ago This video is about 2018 STIHL HT KM POLE SAW SPROCKET REPLACEMENT AND CHANGING THE GEAR GREASE IN THE HEAD. MY CHAIN STOPPED SPINNING...With a little chainsaw maintenance, you can ensure the best performance from your equipment. From using STIHL files and guides to keep your chain sharp to checking that the depth gauge is set correctly, this video shows the proper method on how to sharpen a chainsaw. Learn More. 2 bedroom houses for rent in mesawhat did jschlatt do 1999practical nursing student jobs Mar 3, 2010 · Mar 21, 2010. #5. Fish said: Remove the sawhead and start the unit and see if the shaft is turning, if not. then your problem is from there to the powerhead. If it is, then turn the. input device with a screwdriver and see if it turns the chain, Hi Fish, sorry for big gap in replying- been away. Have taken sawhead off but shaft is not turning. Feb 13, 2021 · A step by step guide to the disassembly and assembly of a Stihl HT-101 pole saw and Stihl HT-75 pole saw shaft assembly. A lot better than the previous one I...